Government Contract | Oregon

Bid Information

Bid Alert No: 00000402521


Agency Bid No. Title: 291-1738-15

Received Date: 10/26/2015

Close Date: 12/01/2015

Purchase Type: 260 Calendar Days from NTP

Delivery Point: Warner Creek Correctional Institution, 20654 Rabbit Hill Road, Lakeview, Oregon, 97630

Delivery Date: Not Stated

Special Notices: Pre-Bid Conference Mandatory 11/05/2015 08:30 AM, Bidder Preregistration


Specifications include, but are not limited to:A. Install hangers for copper tubing with the following maximum horizontal spacing and minimum rod diameters:1. NPS (DN 20) and Smaller: 60 inches (1500 mm) with 3/8-inch (10 mm) rod.2. NPS 1 and NPS 1-1/4 (DN 25 and DN 32): 72 inches (1800 mm) with 3/8-inch (10 mm) rod.3. NPS 1-1/2 and NPS 2 (DN 40 and DN 50): 96 inches (2400 mm) with 3/8-inch (10 mm) rod.4. NPS 2-1/2 (DN 65): 108 inches (2700 mm) with -inch (13 mm) rod.5. NPS 3 to NPS 5 (DN 80 to DN 125): 10 feet (3 m) with -inch (13 mm) rod.6. NPS 6 (DN 150): 10 feet (3 m) with 5/8-inch (16 mm) rod.B. Install supports for vertical copper tubing every 10 feet (3 m).1. NPS 2 (DN 50) and smaller: 48 inches (1200 mm) with 3/8-inch (10 mm) rod.2. NPS 2-1/2 to NPS 3-1/2 (DN 65 to DN 90): 48 inches (1200 mm) with -inch (13 mm) rod.3. NPS 4 and NPS 5 (DN 100 and DN 125): 48 inches (1200 mm) with 5/8-inch (16 mm) rod.4. NPS 6 (DN 150): 48 inches (1200 mm) with -inch (19 mm) rod.ARCHITECTURAL ACCESS DOORS A. Extent of Work: Provide architectural grade access doors at each point of required access to duct features, piping valves, and specialties, concealed equipment, etc. Coordinate this work with other sections for ceilings, walls, etc. B. Material: Steel framed doors with heavy duty hinges and latch type locking mechanisms with surface finish configuration to accept, match or correlate with adjacent surface. 1. Product equivalent to Inland-Ryerson Milcor, Cesco 2. Size adequate to access point of maintenance, to work on and remove concealed devices and equipment. C. Installation: Complete, blended into adjacent work. Anchor sheet metal flashing and trim and other components of the Work securely in place, with provisions for thermal and structural movement. Use fasteners, solder, welding rods, protective coatings, separators, sealants, and other miscellaneous items as required to complete sheet metal flashing and trim system.1. Install sheet metal flashing and trim true to line and levels indicated. Provide uniform, neat seams with minimum exposure of solder, welds, and sealant.2. Install sheet metal flashing and trim to fit substrates and to result in watertight performance. Verify shapes and dimensions of surfaces to be covered before fabricating sheet metal.3. Space cleats not more than 12 inches apart. Anchor each cleat with two fasteners. Bend tabs over fasteners.4. Install exposed sheet metal flashing and trim without excessive oil canning, buckling, and tool marks.5. Install sealant tape where indicated.

Product Codes: 91075, 91444, 91438, 90922, 91450, 91430, 91468, 91473, 91055, 90945, 96894, 91427, 91223, 90976, 91220, 91244, 91453, 91361, 91461

Agency Information

Issuing Agency: State of Oregon Department of Corrections

State: Oregon

Agency Type: State and Local

Contact: Craig Heilman Purchasing/Contracts Division, 3601 State Street, Suite 280, Salem, Oregon, 97301

Phone: 503-373-7508

Fax: 503-371-3161




FREE Market Analysis

Get a FREE 90-Day Market Analysis and see the bids you’ve been missing