Government Contract | South Carolina
one (1) each, new, unused, current model, 60,000# outside type tilt frame & reeving assembly w/auto tarp system

Bid Information

Bid Alert No: 00000410606

Bid Title: one (1) each, new, unused, current model, 60,000# outside type tilt frame & reeving assembly w/auto tarp system

Agency Bid No. Title: 2317/11-19-15

Received Date: 11/04/2015

Close Date: 11/19/2015

Purchase Type: Not Stated

Delivery Point: York, South Carolina

Delivery Date: Not Stated

Special Notices: Bidder Preregistration


Specifications include, but are not limited to:GENERAL: The tilt frame shall be of all steel construction. The tilt angle of the frame shall be at least 45 degrees from vertical when the tilt frame rails are in the full raised position. The tilt frame rails shall rest on a surface roller designed to meet a roadway surface when the tilt frame is mounted on a chassis frame rail approximately 43-inches high and the tilt frame is fully raised.2. FRAME RAILS: The tilt frame shall be equipped with a pair of 8-inch x 4-inch x -inch rectangular rails, reinforced by 1/4 and 1/2 inch steel plate cross members. Each rail shall be equipped with alloy steel guide wear bars spaced at 35 -inches outside to permit support and guide for containers designed for outside rail support. Spring steel wear strips over the outside of rails, or a roller system, shall be provided.3. TILT FRAME LOCKING DEVICE: The frame rails shall have an automatic spring-loaded container locking safety latch that prevents movement of the refuse container during transit. The safety latch shall have a manual feature to provide positive locking to prevent rearward movement of the container during the dumping cycle.4. REAR CONTAINER LOCKS: Rear container locks shall be provided on both tilt frame rails at maximum of 65-inches back of the centerline of the tandem suspension.5. ROLLER STABILIZER: A 10-3/4-inch diameter, 21-1/2-inch wide ground level roller stabilizer shall be provided at the rearmost extremity of the tilt frame rails. The roller shall rotate on a minimum 2-inch diameter shaft.6. PIVOT ASSEMBLY: A pivot assembly shall be provided to permit elevating the forward end of the tilt frame to approximately 45 degrees. The pivot assembly shall be constructed of heavy steel plate, strengthened by steel reinforcements and braced by tubular cross members who also serve as a fulcrum.7. REEVING ASSEMBLY: (60,000 lb. capacity) Reeving shall be accomplished by winding 7/8-inch heavy duty IWRC steel wire rope over four each 12-inch diameter case hardened sheaves. These sheaves shall rotate on a minimum 2-inch diameter shaft. The sheaves shall be bronze bushed and provided with a zerk fitting for lubrication. Two each doubleacting, one stage, chrome plated, telescopic type hydraulic cylinders rated at 60,000 pounds minimum capacity plus 10, move in guide rails on slide blocks with replaceable cast iron guide blocks.8. TARP SYSTEM: The tilt frame shall be equipped with an automatic tarping system equal to the model 6970 Roll Rite stationary design, capable of covering a 40 yard container. Additional metal shall be added in the arm mounting area to protect from damage. The tarping system mast shall be a minimum of 80 tall, measured from the top of the truck frame rail to the bottom of the tarp roller housing.B. HYDRAULIC SYSTEM AND POWER SOURCE1. GENERAL: Hydraulic power shall be by a heavy duty PTO, mounted to the chassis transmission (Allison 3000RDS) and connected by a heavy-duty driveline to the hydraulic pumps.2. PUMP: The pumps shall be a continuous duty gear type with a capacity of no less than 30 gpm at 1200 rpm and operating at a pressure of 1,750 psi.3. CONTROL VALVE: A manually operated control bank shall be provided for control of each hydraulic component. The valve bank shall contain appropriate reverseflow check and shall be sectional in assembly. Controls are to be located inside the cab with a duplicate set located outside of the cab adjacent to the driver's door. A manual throttle advance shall be located outside the cab. An adjustable builtin pressure relief, preset and wire sealed at the design pressure shall be provided.4. OIL RESERVOIR: A minimum 70 gallon potential capacity reservoir tank shall be provided. The tank shall have internal baffling, appropriate drainage opening with plug, a handhole clean out opening with gasket and cover, and filler port with an air breather cap. The system shall be delivered to the York County Maintenance Shop adequately filled with hydraulic oil meeting the manufacturer's requirements for proper long life operation of the system.

Bid Related Documents

Download Document

Product Codes: 06584, 06575

Agency Information

Note to Vendors To access the agency specs go to: WWW.GOVBIDS.COM/SCRIPTS/SC1/PUBLIC/HOME1.ASP. Registration is mandatory and free for BidNet clients. If you are not already registered, login to WWW.BIDNET.COM and select Add eProcurement Systems. For assistance, call BidNets Bid Alert Service Support Center at 1-800-677-1997.

Issuing Agency: County of York/IPT

State: South Carolina

Agency Type: State and Local

Contact: Roddey Bolin 6 South Congress Street, P.O. Box 180, York, South Carolina, 29745

Phone: 803-628-3202




FREE Market Analysis

Get a FREE 90-Day Market Analysis and see the bids you’ve been missing