Government Contract | New Jersey
FURNISH AND DELIVERY OF ONE(1)12'DIAMETER INCLINE GRIT REMOVAL SCREW CONVEYOR AS A FULL REPLACEMENT

Find Open Contracts in the Architecture and Engineering Industry

Find Contracts Now

Bid Information


Bid Alert No: 00000596792

Bid Title: FURNISH AND DELIVERY OF ONE(1)12'DIAMETER INCLINE GRIT REMOVAL SCREW CONVEYOR AS A FULL REPLACEMENT

Agency Bid No. Title: BID2016-51

Received Date: 06/10/2016

Close Date: 06/22/2016

Purchase Type: Not Stated

Delivery Point: Trenton, New Jersey

Delivery Date: Not Stated

Special Notices: Bidder Preregistration

Specifications

Specifications include, but are not limited to:The City of Trenton Sewer Utility is soliciting sealed bids for the furnishing and delivery of one (1) 12"diameter grit removal screw conveyor as a full replacement for the existing conveyor at the SewageTreatment Plant. Large scale shop drawings and equipment field inspections are available for review byappointment at the Trent on Sewer Utility, 609-989-3171. Delivery shall be made to the Trent on SewageTreatment Plant, 1502 Lamberton Road, Trenton, New Jersey 08611.SCREW CONVEYORManufactured by Martin Sprocket and Gear per drawing# 12-8491400, or approved equivalent.1. -12" DIA X 26' X 30 Deg. Incline Grit Screw Conveyor2. -12" DIA X 6" Pitch X 3/8" Thick, Right Hand, Mild Steel, Sectional Flight3. Mounted on a 3" Schedule 40 Pipe, Bushed & 2-Bolt Drill for 2 7/16" Shaft, CWBS4. - 12" X 1/4" Thick Hot Dipped Galvanized (HDG) Trough w/AR 225 Wear Liners5. - (3) 12" Saddle Supports w/ Feet Offset for 30 DEG Incline6. - Martin Sprocket & Gear 12CH2265-0 Hanger Assembly w/ Martin Sprocket & Gear CHB2205-HHanger Bearing7. - Martin Sprocket & Gear CC5H Hardened Bearing Area Coupling Shaft8. - Inlet Flange 13" x 13" inside square w/ (12) 7/16" bolt holes to mate wit h existing horizontalgrit screw conveyor (see Martin drawing# 12-8475763)9. - Discharge Flange 16-1/4 outside diameter (8) 9/16" bolt hole s on a 15" B.C.10. - 10 GA HDG Bolted Covers11. - To include required hardware for assembly12. - Conveyor is to ship in (2) sect ions for ease of transport & storageINLET END GRIT WASHER TANK1. - Same width and material as the conveyor t rough2. - 4' 2-7/16" High as measured from the center of the screw shaft , extending at a 90 Deg. angleto t he screw and extending horizontal to the ground back to the trough3. - Tank is to have 12CFG INLET, 4" NPT full coupling wash water return, and 2" NPTo ne endthreaded pipe nipple drain located in the trough end below the screw shaft4. - Tank is to have a Weir Plate that is adjustable in two places. Adjustment plates are to be 5" tallX 13" wide and have 2" of adjustment. Adjustment is via 9/16" bolt s in a slot ted hole5. - The top cover over the weir plate is to be hinged6. - Tank is to have a 16" X 16" Water tight Inspection/Clean-Out Hatch Located on the right sidewhen viewing from the inlet end

Bid Related Documents

Download Document

Product Codes: 72000, 89000, 91468, 91391

Agency Information


Issuing Agency: City of Trenton

State: New Jersey

Agency Type: State and Local

Contact: Isabel C. Garcia City Hall Annex, 319 East State Street, 1st Floor, Trenton, New Jersey, 08608

Phone: 609-989-3135

Email: igarcia@trentonnj.org

< PREVIOUS PAGE

GET A FREE
MARKET
ANALYSIS

FREE Market Analysis


Get a FREE 90-Day Market Analysis and see the bids you’ve been missing

GET BIDS NOW